The article following next about Installing A Bathtub is especially engaging. Give it a go and make your own conclusions.
Setting up a bathtub isn't specifically rocket science, yet it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a reasonably tough project. If the old tub is readily accessible, the task can relocate immediately; if you need to open up a wall to remove the old tub and also place the new bathtub, the task is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as embeded in the new one. Ensure you have qualified yourself for the job and are comfortable trying it. As opposed to working with a service provider to take control of a halfway-completed job, it is much better to think about employing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This short article will assist you set up a brand-new tub in your restroom if you have already purchased a brand-new bathtub and also do not require to alter the arrangement of your previous water supply pipelines.
Your tools and product list ought to comprise the following:
Getting ready for the Installation
To start with, the sustaining framework supplied with the bathroom ought to be fitted (if required) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be suited its final position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is separate the water system. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome due to the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have actually been eliminated, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning throughout this process. When the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Before carrying on to fit the new taps, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Making use of the two wood boards under its feet, place the tub in the called for setting. The wood boards are useful in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four tiny points.
The next objective is to guarantee that the tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the bath tub until the spirit level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap port to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Switch on the water system and also check all joints as well as brand-new pipework for leakages and tighten them if needed. Load the bathtub and additionally check the overflow outlet as well as the regular outlet for leaks.
Lastly, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the bath tub has actually been used at least once as this will certainly resolve it into its last position.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and also the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier provided backnut. Once the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap ports. The former type ought to be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a stiff seal, triggering the water to penetrate the wall in between the bath and the tiling, leading to complications with wetness and also possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealant can fracture relatively early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was shown that editorial on Installing A Bathtub from someone on our other blog. Sharing is good. You won't know, you could be doing someone a favor. Thank you for your time. Come back soon.
Show Details